This thumb-actuated device accepts 5- and 10-mL syringes. Each click of the thumb-switch pushes down the piston a set amount. Photo courtesy Tridak LLC
Inexpensive, fast, flexible and easy to operate, these systems can be handheld or mounted to a Cartesian robot. Syringes are available in sizes ranging from 3 to 55 cc. When the syringe is empty, it’s thrown away. No cleaning is required.
“By changing the time and pressure, you get different quantities of adhesive,” says Tom Bray, applications design engineer at Hernon Manufacturing Inc. “You can dispense a wide range of materials, from very low-viscosity liquids to very high-viscosity pastes.”
Finding the right combination of time and pressure for a particular material requires some experimentation. “You want to start with shortest time, lowest pressure and smallest tip you can,” says Bray. “From there, you work your way up: more time, more pressure, bigger needle.”
Although time-pressure systems have been around for decades, the technology has not remained static. Indeed, equipment suppliers have recently introduced a number of improvements to the technology.
One of those improvements has been digital control. In the past, when operators wanted to adjust time or pressure, they turned dials. Now, operators enter in the exact numerical settings.
“Instead of a potentiometer or an internal timer, you have digital readouts,” says Vladimir Siroky, director of operations at Fisnar Inc.
Digital control also gives engineers the ability to store and recall time- pressure settings for specific materials. It also permits them to lock settings to prevent operator adjustment, and it enables them to program automatic adjustments to those parameters over time.
This digital dispenser automatically adjusts time and pressure settings
at set intervals of time or amounts of deposits. Photo courtesy EFD Inc.
Problems and Solutions
For the most part, time-pressure dispensers are very repeatable, says Bray. Two common sources of variability in shot size are fluctuations in air pressure and material temperature. The former can be addressed with a precision pressure regulator. The latter can be addressed by warming or insulating the material supply.One problem with time-pressure systems is that their performance can decline as the syringe empties. Less time and pressure are needed to dispense a given volume from a syringe with 25 cc of adhesive and 5 cc of air than from a syringe with 5 cc of adhesive and 25 cc of air. As a result, if time and pressure settings remain constant, the shot size can diminish over time.
Assemblers can overcome that problem by dispensing from smaller syringes or starting with syringes that are less than full. “That way, there’s less of a [volume difference] between a full syringe and an empty one,” says Mike Vidal, engineering manager at EFD Inc.
EFD has come up with its own solution to the problem that doesn’t require any sort of adjustments or volume compromises. It’s called the Optimeter. The central component of the Optimeter is a cone-shaped pin. The base of the cone is connected to the piston inside the syringe.
When the syringe is full, the narrow end of the cone passes through the air hole of the end cap, limiting how much air pressure can be applied to the piston, explains Vidal. As the syringe empties, the cone moves down with the piston, gradually retracting from the air hole and allowing more pressure to act on the piston.
“What’s nice about the Optimeter is that it’s passive,” says Vidal. “You don’t have any fancy electronics or feedback loops. It’s like a spigot. As the barrel empties, it opens up the flow more. You get the same pressure pulse with a full barrel as you get with an empty barrel.”
The Optimeter is available for 10- and 30-cc syringe barrels. “The taper on the pin is optimized for each barrel size,” says Vidal.
Another common issue with time- pressure dispensers lies with reactive materials, such as epoxies, that change in viscosity over time. As these materials thicken, more pressure, time or both are needed to maintain a consistent deposit size. If time and pressure settings remain constant, the shot size will decrease over time.
Here, too, suppliers are rising to the challenge. For example, the Ultimus V digital dispenser from EFD can be programmed to match the viscosity changes of the material, automatically adjusting time and pressure settings at set intervals of time or amounts of deposits.
For instance, say an epoxy becomes markedly thicker 10 minutes after it’s mixed, and thicker still 20 minutes later. An engineer can program the unit to dispense at a certain time and pressure for the first 10 minutes, another time and pressure for the next 20 minutes, and a third time and pressure for the remaining material. Alternatively, the unit could be programmed to dispense at a certain time and pressure for the first 200 shots, another time and pressure for the next 400 shots, and a third time and pressure for the remaining material.
“There is some up-front work that has to be done to understand the viscosity profile of the material,” notes Vidal. “However, once you develop the profile, the material is generally going to behave in the same way.”
For high-volume dispensing with a time-pressure system, the syringe can be replaced with a pressurized reservoir. Photo courtesy Hernon Manufacturing Inc.
Time-Pressure Alternatives
Time-pressure dispensing systems can be handheld or mounted to a
Cartesian robot. Photo courtesy Fisnar Inc.
An interference fit between the piston and the syringe prevents pressure loss and keeps material from slipping past the piston, says Gleason. In addition, the piston can be programmed to pull back after each dot is dispensed, which keeps material from oozing out of the tip.
With a 3-cc syringe, a leadscrew for large volumes can dispense dots as small as 0.0009 cc with a standard deviation of three sigma. A leadscrew for small volumes can put down dots as small as 0.00023 cc.
Another motor-driven alternative to the time-pressure unit is a peristaltic pump dispenser. As with a pinch-tube system, the adhesive travels from a reservoir to the dispense tip via flexible tubing. Instead of using compressed air to force out the adhesive, a rotor turns a series of rollers that press against the tubing. With each turn of the rotor, the rollers push a set amount of adhesive forward in the tubing.
“It works like your esophagus,” says Siroky. “It’s a positive-displacement technology, and it’s very easy to control.”
Because it’s a closed system, the device is ideal for dispensing volatile or hard-to-work-with materials. Safe for use in clean rooms, the peristaltic pump can operate in manual or timed modes. Reversing the rollers slightly produces a suck-back to prevent drips from the dispense tip. Equipped with a Teflon tube, it can output 0.01 to 6 mL/min. With a silicone tube, it can put out 0.1 to 20 mL/min.
On the opposite end of the spectrum, assemblers can avoid any electromechanical control at all with a device like the Microdot from Tridak. This thumb-actuated device accepts 5- and 10-mL syringes. Each click of the thumb switch pushes the piston down a set amount. Shot size is adjusted using a knurled knob near the top of the unit, and a safety lock prevents accidental actuation.
“The Microdot allows you to move around freely, and you get a very repeatable shot with each click,” says Cole. “We have customers who use it for doing rework in warehouses. They can take all the adhesives they need with them and just use the one dispenser.”
When dispensing a material with a viscosity of 400 centipoise, the device can put down a shot as small as 0.003 mL with a 25-gauge taper tip or as large as 0.17 mL with a 14-gauge taper tip.
This story was originally published in Assembly magazine, January 2010.
