Schematic shows the change in vertically aligned multi-walled carbon nanotubes during adhesion measurements.
Scientists have long been interested in the ability of gecko lizards to scurry up walls and cling to ceilings by their toes. The creatures owe this amazing ability to microscopic branched elastic hairs in their toes that take advantage of atomic-scale attractive forces to grip surfaces and support surprisingly heavy loads. Several research groups have attempted to mimic those hairs with structures made of polymers or carbon nanotubes.
In a paper published in the October 10, 2008, issue ofScience, researchers from the University of Dayton, the Georgia Institute of Technology, the Air Force Research Laboratory and the University of Akron describe an improved carbon nanotube-based material that, for the first time, creates directionally varied (anisotropic) adhesive force. With a gripping ability of nearly three times the previous record - and 10 times better than a real gecko at resisting perpendicular shear forces - the new carbon nanotube array could give artificial gecko feet the ability to both tightly grip vertical surfaces and be easily lifted off.
Beyond the ability to walk on walls, the material could have many technological applications, including connecting electronic devices and substituting for conventional adhesives in the dry vacuum of space.
The research was sponsored by the National Science Foundation and the U.S. Air Force Research Laboratory at Wright-Patterson Air Force Base near Dayton, OH.
“The resistance to shear force keeps the nanotube adhesive attached very strongly to the vertical surface, but you can still remove it from the surface by pulling away from the surface in a normal direction,” said Liming Dai, the Wright Brothers Institute endowed chair in the University of Dayton School of Engineering. “This directional difference in the adhesion force is a significant improvement that could help make this material useful as a transient adhesive.”
The key to the new material is the use of rationally designed multi-walled carbon nanotubes formed into arrays with “curly entangled tops,” said Zhong Lin Wang, a Regents’ Professor in the Georgia Tech School of Materials Science and Engineering. The tops, which Wang compared to spaghetti or a jungle of vines, mimic the hierarchical structure of real gecko feet, which include branching hairs of different diameters.
Scanning electron microscope image of the vertically aligned multi-walled carbon nanotubes grown for this research.
“The contact surface area matters a lot,” he said. “When you have line contact along, you have van der Waals forces acting along the entire length of the nanotubes, but when you have a point contact, the van der Waals forces act only at the tip of the nanotubes. That allows us to truly mimic what the gecko does naturally.”
In tests done on a variety of surfaces - including glass, a polymer sheet, Teflon and even rough sandpaper - the researchers measured adhesive forces of up to 100 Newtons per square centimeter in the shear direction. In the normal direction, the adhesive forces were 10 Newtons per square centimeter - about the same as a real gecko.
The resistance to shear increased with the length of the nanotubes, while the resistance to normal force was independent of tube length.
Though the material might seem most appropriate for use by Spider-Man, the real applications may be less glamorous. Because carbon nanotubes conduct heat and electrical current, the dry adhesive arrays could be used to connect electronic devices.
“Thermal management is a real problem today in electronics, and if you could use a nanotube dry adhesive, you could simply apply the devices and allow van der Waals forces to hold them together,” Wang said. “That would eliminate the heat required for soldering.”
Another application might be for adhesives that work long-term in space. “In space, there is a vacuum, and traditional kinds of adhesives dry out,” Dai said. “But nanotube dry adhesives would not be bothered by the space environment.”
In addition to those mentioned, the research team included Liangti Qu from the University of Dayton, Morley Stone from the Air Force Research Laboratory and Zhenhai Xia from the University of Akron.
A heavy metal ring is supported from a sandpaper surface by a small square of carbon nanotube dry adhesive.
Qu noted that sample purity was another key factor in ensuring strong adhesion for the carbon nanotube dry adhesive.
In the future, the researchers hope to learn more about the surface interactions so they can further increase the adhesive force. They also want to study the adhesive’s long-term durability, which, in a small number of tests, became stronger with each attachment.
In addition, they may also determine how much adhesive might be necessary to support a human wearing tights and a red mask.
“Because the surfaces may not be uniform, the adhesive force produced by a larger patch may not increase linearly with the size,” Dai said. “There is much we still need to learn about the contact between nanotubes and different surfaces.”
For more information, contact John Toon, phone (404) 894-6986, e-mail jtoon@gatech.edu; or Abby Vogel, phone (404) 385-3364, e-mail avogel@gatech.edu.
